4AppsApk.com try to give the Latest Version of "Ampere Pro 2.13 Apk" for your Android Phone. This App belongs to the 2019 Best Android Apps category. This APK file last updated on November 8, 2017 at 6:57 pm. Choose and download from the below direct download link to start get the apk file for "Ampere Pro 2.13 Apk", And then move the file to your Android phone's SD card and use one file manager you prefer to browse & install it. you will need Android 4.0.3 version or higher to install this app.
Ampere Pro 2.13 Apk
Did you ever felt, that one Charger/USB cable set charges your device really fast and the other not? Now, you can prove this with Ampere.
Measure the charging and discharging current of your battery.
The app works on Android 4.0.3+ devices. Not every device is supported because there are devices which lacks an appropriate measurement chip (or the interface) and they can not be supported at all. Please read the list of not supported phones at the end of the description.
The app is not meant to be mA accurate. It is only good for evaluate which Charger/USB cable combo is working the best for you on the same device.
Start the app and wait ca. 10 seconds (“measuring” is on the display). After this time, the charging or discharging current will be shown.
The current depends on many things:
– The charger (USB/AC/Wireless)
– The USB cable
– The phone type
– Current tasks running
– Display brightness
– WiFi state
– GPS state
Please don’t use the readings on this app as concrete science. However, the readings are good enough to relatively measure how various chargers and USB cables fair on the same device.
If your Lollipop device (or later) shows 0 all the time, please use the settings option “Old measurement method”. You can force the app with it to use the old measurement interface, if the Lollipop device has at least one. Maybe it helps…
Unfortunately some Samsung devices don’t give correct (measured) values (e.g.: S5), just the maximum possible charging current with the actual USB cable/charger configuration. This is a firmware problem.
About notification and background measurement:
– The measurement works in the background only if you switch on the notification in the settings.
– You can hide the notification icon by setting the notification priority to minimum.
Background info: The app measures the charging/discharging current of the battery. If your phone is not connected to a charger, you see the discharging current which is negative. If you connect a charger then the current what the charger gives will be used to supply your phone and the remaining power will be charged into the battery.
If your phone consumes 300 mA without a charger connected (-300mA on the display), then a 500 mA charger will charge your battery maximum with 200 mA current (200mA on display).
Technical info: The displayed current is an average value from 50 measurements minus the 10 upper values and the 10 lower values. The displayed current can be shaky or unstable or even just zero which means, that the Android system provides such unstable values. Every company uses different battery types and other hardware making it difficult to get accurate results about your charger.
LiPo batteries don’t draw the maximum for the full time it takes to charge the phone. If your battery is charged almost full then the charging current will be much less as by lower battery levels.
A graph explaining LiPo charge stages: http://batteryuniversity.com/_img/content/ion1.jpg
Dave’s (EEVBlog) LiPo Charging Tutorial: http://youtu.be/A6mKd5_-abk
Phones/ROMS compatible only with “Old measurement method” switched on and selected the right “Measurement interface”:
➤ HTC One M7 / M8
Phones/ROMS reported to be not working with this app:
➤ Galaxy Grand Prime – fortuna3gdtv
➤ Galaxy Note2 – t03g, t03gchn, t03gchnduos, t03gcmcc, t03gctc, t03gcuduos
➤ Galaxy S3 – d2att, d2spr, d2vmu
➤ Galaxy Tab4 7.0 – degas3g
➤ HTC Desire 510 – htc_a11ul8x26
➤ HTC One S (ville), X (endeavoru), XL (evita)
➤ HTC Sensation 4G – pyramid
Please do not give wrong rating, if your phone is one of the above. Not the app is wrong, but your phone does not support this kind of measurement yet.
If the app doesn’t work on your device with pre-Lollipop Android version, then please read the first and the second posts in this XDA developer forum thread: http://spam.com/pZqJg8 . Please post your problem with screenshots in the XDA thread.
* Android Oreo compatibility enhancements
* Language updates
* Bug fixes
Ampere FAQ: http://goo.gl/R8XgXX
For more info please read the change history: Settings => About Ampere => Change history
Note: When ampere would stuck in “measuring” state (after a firmware upgrade to Android 7.x) please clear Amperes’s app cache.
1.) Open the “Android Settings app” => “Apps” => “Ampere”
2.) Clear all data under the “Storage” menu
3.) Restart Ampere
App name : Ampere
Package Name : com.gombosdev.ampere
Apk Md5 : 69d4091988d6d3678aaf1b4ab85ace4d
Apk Size : 6.21 MB
Update on Play Store : November 4, 2017
Version Name & Code: 2.13 (187)
Requirements: 4.0.3 and up